Page 412 - Tungaloy Catalog

Cartridges

CAE R/L External grooving and traversing

ar

f
W L1

Right hand (R) shown.
Insert Stock * Max. Dimensions (inch) Parts
seat Cat. No. groove depth Inserts Shank
size R L ar (inch) L1 f W Clamping screw Wrench
3 CAER/L-3T16   0.630 1.772 0.409 0.118 DGS / SGS
4 CAER/L-4T16   0.630 1.772 0.413 0.157 DGM / SGM CHFVR/L BHM6-20-A P-4
DTX, DTE,
5 CAER/L-5T20   0.787 1.929 0.413 0.197 DTR, CHSR/L
6 6 CAER/L-6T20   0.787 1.929 0.413 0.236 SGN-QBN
CAF R/L Face grooving and traversing

Parting and Grooving Tools f ar øDmax
L1
W

øDm

Max.
Dimensions (inch)
Insert
Parts
groove
øDm
øDm
seat
depth
L
Clamping screw Wrench
(inch)
(inch)
size Cat. No. R Stock Min. dia. Max. dia. ar (inch) L1 f (2) W Inserts (3) Shank Right hand (R) shown.
CAFR/L-3T12-040055   1.575 2.165 0.472 1.772 0.409 0.118 DTF
CAFR/L-3T12-055075   2.165 2.953 0.472 1.772 0.409 0.118
3 CAFR/L-3T12-075100   2.953 3.937 0.472 1.772 0.409 0.118 BHM6-20-A P-4
CAFR/L-3T12-100140   3.937 5.512 0.472 1.772 0.409 0.118
CAFR/L-3T12-140200   5.512 7.874 0.472 1.772 0.409 0.118
CAFR/L-4T16-050070   1.969 2.756 0.630 1.772 0.413 0.157
CAFR/L-4T16-070100   2.756 3.937 0.630 1.772 0.413 0.157
4 BHM6-20-A P-4
CAFR/L-4T16-100150   3.937 5.906 0.630 1.772 0.413 0.157 DTF
CAFR/L-4T16-150250   5.906 9.843 0.630 1.772 0.413 0.157 DTE CHFVR/L
DTX
CAFR/L-5T20-055080   2.165 3.150 0.787 1.929 0.413 0.197 DGS CHSR/L
CAFR/L-5T20-080120   3.150 4.724 0.787 1.929 0.413 0.197 DGM
5 CAFR/L-5T20-120180   4.724 7.087 0.787 1.929 0.413 0.197 DTR BHM6-20-A P-4
CAFR/L-5T20-180300   7.087 11.811 0.787 1.929 0.413 0.197
CAFR/L-5T20-300000   11.811 ∞ 0.787 1.929 0.413 0.197
CAFR/L-6T25-060090   2.362 3.543 0.984 (1) 2.165 0.413 0.236
6 CAFR/L-6T25-090150   3.543 5.906 0.984 (1) 2.165 0.413 0.236 BHM6-20-A P-4
(1)
CAFR/L-6T25-150250   5.906 9.843 0.984 2.165 0.413 0.236
CAFR/L-6T25-250400   9.843 15.748 0.984 (1) 2.165 0.413 0.236
(1) When depth is deeper than insert length, 1 corner type is
recommended. (3) Min. diameter øDm of DTE, DGS and DGM insert
(2) “f” value in the above table is calculated with groove width “W” Inserts øDm
shown in the table. (inch) Note
DTE3 / DGS3 / DGM3 ø1.733 When diameter is smaller
Caution DTE4 / DGS4 / DGM4 ø1.654
In DTF and DTX insert types, seat size “6” inserts are not DTE5 / DGS5 / DGM5 ø1.969 than øDm, DTF or DTX type
insert is recommended.
available. When 6 size insert is required, the DTE, DGM or DGS DTE6 / DGS6 / DGM6 ø1.890
type is recommended.

6–32